NeoPixel Jewel - 7 x 5050 RGBW LED w/ Integrated Drivers - Warm White - ~3000K

Circular PCB with 7 WS2812-compatible 5050 RGBW LEDs (red, green, blue, white); each has an integrated driver. Powered at 5V via a single data line. Chainable; includes mounting holes. Dedicated white channel enables more accurate white output than RGB mixing.

Logical pinout · physical placement not verified

5V
NeoPixel Jewel power input. Adafruit product page states to power the board with 5VDC and that 4-7V works.
Type · PowerVoltage · 5VDC nominal; 4-7V supported by source
GND
Ground / negative return. Adafruit NeoPixel guide identifies the same three inputs as +5V, ground, and data, and connects GND to the controller/power ground.
Type · GroundVoltage · 0V
DINDI
NeoPixel data input. Adafruit guide says the input end may be labelled DIN or DI, and the product page says a single data line controls the chain.
Type · Signal
DOUTdata out
NeoPixel chain output from this Jewel to the input of another. Adafruit product page states the LEDs are chainable by connecting the output of one Jewel into the input of another.
Type · Signal

Pin	Type	Function	Voltage
5V	Power	NeoPixel Jewel power input. Adafruit product page states to power the board with 5VDC and that 4-7V works.	5VDC nominal; 4-7V supported by source
GND	Ground	Ground / negative return. Adafruit NeoPixel guide identifies the same three inputs as +5V, ground, and data, and connects GND to the controller/power ground.	0V
DINDI	Signal	NeoPixel data input. Adafruit guide says the input end may be labelled DIN or DI, and the product page says a single data line controls the chain.
DOUTdata out	Signal	NeoPixel chain output from this Jewel to the input of another. Adafruit product page states the LEDs are chainable by connecting the output of one Jewel into the input of another.

Logical pinout · physical placement not verified

Pin details

4 connections

5V
NeoPixel Jewel power input. Adafruit product page states to power the board with 5VDC and that 4-7V works.
PowerVoltage · 5VDC nominal; 4-7V supported by source
GND
Ground / negative return. Adafruit NeoPixel guide identifies the same three inputs as +5V, ground, and data, and connects GND to the controller/power ground.
GroundVoltage · 0V
DINDI
NeoPixel data input. Adafruit guide says the input end may be labelled DIN or DI, and the product page says a single data line controls the chain.
Signal
DOUTdata out
NeoPixel chain output from this Jewel to the input of another. Adafruit product page states the LEDs are chainable by connecting the output of one Jewel into the input of another.
Signal

LED pixels

179 other options

WS2812/SK6812 NeoPixel strips, rings and Jewels, APA102 DotStar pixels, and plain analog RGB strips — each matched to its protocol and host, not just its connector.

View all 179

Related groups

4 groups

Bare ICs

74HC logic gates, MCP3008/MCP23017 ADCs and expanders, 24LC256 EEPROM, 4N25-series optocouplers and ULN2803A drivers — bare DIP chips with no breakout-board conveniences like pull-ups or level shifting.

Components · Integrated circuits · 68 parts

Converters

ADS1115/MCP3421 ADCs, MCP4725 and GP8413 DACs, CP2102 USB-UART boards, and I2C plumbing like the LTC4316 address shifter — matched to bus, resolution and signal range.

Components · Interface converters · 114 parts

Memory

24LC32/25LC256 EEPROM, I2C FRAM, 64Mbit PSRAM, and microSD breakouts up to 64GB — matched to write frequency and data volume, not just interface.

Components · Memory & storage · 39 parts

Passives

E12 resistor kits, ceramic and electrolytic capacitor sets, 1N4148/1N4007 diodes, TIP120 Darlingtons, IRLZ44N MOSFETs and 100F supercapacitors — bench stock in kit quantities.

Components · Passives · 58 parts