
Add motion, direction and orientation sensing to your Arduino project with this all-in-one 9-DOF sensor. Inside the chip are three sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity) or how fast the…
Breakout power input. Adafruit Learn states the breakout accepts 3-5VDC and has onboard regulators/level shifting.
Ground for power and signal.
3.3V regulator output from the breakout, about 100mA available.
I2C clock. Also used as SPI clock; level shifted for 3-5V logic input.
I2C data. Also used as SPI MOSI; level shifted for 3-5V logic input.
I2C · SPI · 3-5VDC input · 0V
Confirm the data interface matches your host board.
Module pins: VIN, 3Vo, GND, SCL, SDA, CSG, CSXM, SDOG. Schematik maps them to your board in the app.
SparkFun Qwiic Pro Micro BoogieBoard visual preview
9V to Barrel Jack Adapter visual preview
SparkFun 16x2 SerLCD - RGB Backlight (Qwiic) visual preview
MicroUSB Plug to 5.5/2.1mm DC Barrel Jack Adapter | Kiwi Electronics visual previewSort passive connector adapters from Qwiic boards, LCD modules and microSD card adapters before assuming anything with the right plug will substitute safely.
Connectors & cables · Connectors · 28 parts
RGB backlight positive LCD 16x2 visual preview
SparkFun 16x2 SerLCD - RGB Backlight (Qwiic) visual preview
I2C 20x4 Arduino LCD Display Module visual preview
Gravity: I2C 16x2 Arduino LCD with RGB Backlight Display V2.0 visual previewCharacter LCDs, SPI TFTs, e-paper modules and larger capacitive-touch TFT panels solve different display jobs. Treat display class, interface, controller, resolution, touch, refresh behaviour, storage, voltage and mounting as separate swap checks.
Displays · TFT & LCD displays · 35 parts
MQ-2 Gas Sensor visual preview
MQ-3 Gas Sensor visual preview
MQ-135 Gas Sensor visual preview
Grove - Air quality sensor visual previewChoose between MQ gas sensors, VOC/eCO2 indoor-air sensors, true CO2 modules and particulate sensors without treating every air-quality breakout as the same detector.
Sensors · Gas & air-quality sensors · 31 parts
Raspberry Pi Pico visual preview
Adafruit Feather nRF52840 Express visual preview
Pan-Tilt HAT kit visual previewESP32, Arduino Uno, Raspberry Pi Pico, and compatible add-on boards for running builds.
Boards · Microcontroller boards · 24 parts
Gyro subchip SPI chip select; level shifted for 3-5V logic input.
Accelerometer/magnetometer subchip SPI chip select; level shifted for 3-5V logic input.
Gyro subchip SPI MISO output. Adafruit states it is 3V logic out and readable by 5V logic chips.
Accelerometer/magnetometer subchip SPI MISO output. Adafruit states it is 3V logic out and readable by 5V logic chips.
Gyro data enable input; Adafruit describes it as level shifted.
Accelerometer/magnetometer interrupt output.
Accelerometer/magnetometer interrupt output.
Gyro data-ready output.
Gyro interrupt output.
| Pin | Position | Type | Function | Voltage |
|---|---|---|---|---|
| VIN | power | Breakout power input. Adafruit Learn states the breakout accepts 3-5VDC and has onboard regulators/level shifting. | 3-5VDC input | |
| GND | ground | Ground for power and signal. | 0V | |
| 3Vo | power | 3.3V regulator output from the breakout, about 100mA available. | 3.3V output | |
| SCL | signal | I2C clock. Also used as SPI clock; level shifted for 3-5V logic input. | 3-5V logic input when used as SPI clock | |
| SDA | signal | I2C data. Also used as SPI MOSI; level shifted for 3-5V logic input. | 3-5V logic input when used as SPI MOSI | |
| CSG | signal | Gyro subchip SPI chip select; level shifted for 3-5V logic input. | 3-5V logic input | |
| CSXM | signal | Accelerometer/magnetometer subchip SPI chip select; level shifted for 3-5V logic input. | 3-5V logic input | |
| SDOG | signal | Gyro subchip SPI MISO output. Adafruit states it is 3V logic out and readable by 5V logic chips. | 3V logic output | |
| SDOXM | signal | Accelerometer/magnetometer subchip SPI MISO output. Adafruit states it is 3V logic out and readable by 5V logic chips. | 3V logic output | |
| DEN | signal | Gyro data enable input; Adafruit describes it as level shifted. | level-shifted input | |
| INT1 | signal | Accelerometer/magnetometer interrupt output. | 3V logic output | |
| INT2 | signal | Accelerometer/magnetometer interrupt output. | 3V logic output | |
| DRDY | signal | Gyro data-ready output. | 3V logic output | |
| INTG | signal | Gyro interrupt output. | 3V logic output |