NeoPixel Jewel - 7 x 5050 RGB LED with Integrated Drivers

Be the belle of the ball with the NeoPixel Jewel! We fit seven of our tiny 5050 (5mm x 5mm) smart RGB LEDs onto a beautiful, round PCB with mounting holes and a chainable design to create what we think is our most elegant (and evening-wear appropriate) NeoPixel board yet.

5V
NeoPixel Jewel power input. Adafruit product page states to power the board with 5VDC; the NeoPixel guide describes +5V as the positive power input.
Type · powerVoltage · 5V DC
GND
Ground return for the NeoPixel Jewel power and controller reference. The NeoPixel guide states GND must connect to the supply minus terminal and microcontroller GND.
Type · groundVoltage · 0V reference
DIN / DI
Single NeoPixel data input from a microcontroller. The product page states there is a single timing-specific data line and the guide identifies DIN/DI as data input.
Type · signalVoltage · 5V data preferred when powered from 5V; 3.3V data is acceptable when NeoPixels are powered from a 3.7V LiPo per Adafruit guide
DOUT / DO
Data output for chaining to the DIN/DI input of the next NeoPixel Jewel. The product page states LEDs are chainable by connecting output of one Jewel into input of another; the guide says DOUT/DO may be left unconnected at the end of a chain.
Type · signalVoltage · NeoPixel data output

Start wiring

I2S · 5V DC · 0V reference

Verify supply voltage and logic levels before powering up.

Module pins: 5V, GND, DIN / DI, DOUT / DO. Schematik maps them to your board in the app.

Related groups

4 groups

Displays

Character LCDs, SPI TFTs, e-paper modules and larger capacitive-touch TFT panels solve different display jobs. Treat display class, interface, controller, resolution, touch, refresh behaviour, storage, voltage and mounting as separate swap checks.

Displays · TFT & LCD displays · 35 parts

Connectors

Sort passive connector adapters from Qwiic boards, LCD modules and microSD card adapters before assuming anything with the right plug will substitute safely.

Connectors & cables · Connectors · 28 parts

Air quality

Choose between MQ gas sensors, VOC/eCO2 indoor-air sensors, true CO2 modules and particulate sensors without treating every air-quality breakout as the same detector.

Sensors · Gas & air-quality sensors · 31 parts

MCUs and boards

ESP32, Arduino Uno, Raspberry Pi Pico, and compatible add-on boards for running builds.

Boards · Microcontroller boards · 25 parts

5V	power	NeoPixel Jewel power input. Adafruit product page states to power the board with 5VDC; the NeoPixel guide describes +5V as the positive power input.	5V DC
GND	ground	Ground return for the NeoPixel Jewel power and controller reference. The NeoPixel guide states GND must connect to the supply minus terminal and microcontroller GND.	0V reference
DIN / DI	signal	Single NeoPixel data input from a microcontroller. The product page states there is a single timing-specific data line and the guide identifies DIN/DI as data input.	5V data preferred when powered from 5V; 3.3V data is acceptable when NeoPixels are powered from a 3.7V LiPo per Adafruit guide
DOUT / DO	signal	Data output for chaining to the DIN/DI input of the next NeoPixel Jewel. The product page states LEDs are chainable by connecting output of one Jewel into input of another; the guide says DOUT/DO may be left unconnected at the end of a chain.	NeoPixel data output

Pinout

Start wiring

Displays

Connectors

Air quality

MCUs and boards