ChronoDot - Ultra-precise Real Time Clock

RTC breakout based on the MAX31328 temperature-compensated oscillator (TCXO); pin- and code-compatible with DS3231-based ChronoDots. Communicates over I2C; battery-backed to maintain time when main power is removed.

VCC
Main supply input for the ChronoDot when connected to a microcontroller; official macetech docs say VCC powers the module during controller use.
Type · powerVoltage · 2.3V to 5.5V DC per official macetech ChronoDot V3 documentation.
GND
Ground reference for the ChronoDot supply and I2C interface.
Type · groundVoltage · 0V
BAT
Battery node connected directly to the CR1632 cell; official docs say it can be used for an external battery or battery-health monitoring and must not be shorted.
Type · powerVoltage · 3V lithium CR1632 battery node per official macetech documentation.
SDA
I2C serial data line used to communicate with the ChronoDot RTC and onboard EEPROM.
Type · i2c
SCL
I2C serial clock line used to communicate with the ChronoDot RTC and onboard EEPROM.

RTC & timing

26 other options

DS3231/DS3232 temperature-compensated RTCs, the budget PCF8523 and DS1307, the Si5351A clock generator (8kHz–160MHz), and bare 16MHz crystals — matched to drift tolerance and supply voltage.

View all 26

RTC Module - Super Capacitor visual preview

Related groups

4 groups

LED pixels

WS2812/SK6812 NeoPixel strips, rings and Jewels, APA102 DotStar pixels, and plain analog RGB strips — each matched to its protocol and host, not just its connector.

Components · Addressable LEDs · 176 parts

Bare ICs

74HC logic gates, MCP3008/MCP23017 ADCs and expanders, 24LC256 EEPROM, 4N25-series optocouplers and ULN2803A drivers — bare DIP chips with no breakout-board conveniences like pull-ups or level shifting.

Components · Integrated circuits · 68 parts

Converters

ADS1115/MCP3421 ADCs, MCP4725 and GP8413 DACs, CP2102 USB-UART boards, and I2C plumbing like the LTC4316 address shifter — matched to bus, resolution and signal range.

Components · Interface converters · 115 parts

Memory

24LC32/25LC256 EEPROM, I2C FRAM, 64Mbit PSRAM, and microSD breakouts up to 64GB — matched to write frequency and data volume, not just interface.

Components · Memory & storage · 39 parts

Pin	Type	Function	Voltage
VCC	power	Main supply input for the ChronoDot when connected to a microcontroller; official macetech docs say VCC powers the module during controller use.	2.3V to 5.5V DC per official macetech ChronoDot V3 documentation.
GND	ground	Ground reference for the ChronoDot supply and I2C interface.	0V
BAT	power	Battery node connected directly to the CR1632 cell; official docs say it can be used for an external battery or battery-health monitoring and must not be shorted.	3V lithium CR1632 battery node per official macetech documentation.
SDA	i2c	I2C serial data line used to communicate with the ChronoDot RTC and onboard EEPROM.
SCL	i2c	I2C serial clock line used to communicate with the ChronoDot RTC and onboard EEPROM.
RST	reset	Active-low reset signal; official docs state it asserts below about 2.5V VCC or when externally pulled low, without affecting timekeeping.	Active-low; asserts when VCC is less than about 2.5V per official docs.
SQW	digital output	Configurable square-wave or alarm-trigger output; official docs list 1 Hz, 1024 Hz, 4096 Hz, and 8192 Hz modes and note it needs a pull-up to VCC when used.	Open-drain style output requiring pull-up to VCC when used; 10K suggested by official docs.
32K	clock output	32768 Hz open-drain clock output for use as an accurate oscillator reference when enabled.	Open-drain output requiring pull-up resistor per official docs.

Pinout

LED pixels

Bare ICs

Converters

Memory