
Atmel ATWINC1500 802.11bgn WiFi module breakout with SPI interface, SSL/TLS support, and FCC certification. Operates at 3.3 V logic; a level-shifter or 5 V-tolerant host is not needed if using a 3.3 V MCU.
Power input for the ATWINC1500 breakout. Source: Adafruit Learn pinouts.
Ground for signal and power. Source: Adafruit Learn pinouts.
SPI clock input. Source: Adafruit Learn pinouts.
SPI data output from module. Source: Adafruit Learn pinouts.
SPI data input to module. Source: Adafruit Learn pinouts.
SPI · UART · Ethernet · 3.3 – 5 V · Breakout
DFRobot describes DFR0174 as an XBee USB Adapter V2 with an Atmega8U2 programmed as a USB-to-serial converter, Micro USB, XBee socket com…
Module pins: VIN, GND, SCK, MISO, MOSI, CS, RXD, TXD. Schematik maps them to your board in the app.
ESP8285, ATWINC1500, and EMW3060 Wi-Fi modules; the WIZ5500 Ethernet co-processor; the DP83848 RMII PHY board; 802.11n USB adapters for the Pi; and an XBee USB configuration adapter.
MDBT50Q-1M nRF52840 Based BLE Module visual preview
MDBT50Q-P1M nRF52840 BLE Module visual preview
Bluetooth 4.0 Low Energy - BLE Mini visual preview
Bluetooth 4.0 NRF51822 Motherboard (BLE400) visual previewBLE 5-era modules (nRF52840, MDBT50Q), XIAO MG24 boards with Matter-over-Thread, Bluefruit UART/SPI bridges, HM-11 serial modules, and BLE sniffers cover different jobs and different hosts.
Wireless & comms · Bluetooth modules · 73 parts
600-6000MHz 5G Antenna visual preview
A7670E LTE Cat-1 HAT for Raspberry Pi visual preview
Adafruit FONA - Mini Cellular GSM Breakout uFL Version visual preview
Adafruit FONA 3G Cellular + GPS Breakout - European (SIM5320E) visual previewAdafruit FONA GSM breakouts, the Gravity Air780EU 4G Cat 1 module, Dragino NB-IoT Shield-B8, Pycom FiPy, Quectel and SIMCom M.2 5G modems, and the RockBLOCK 9603 Iridium modem each target a different network tier.
Wireless & comms · Cellular · 58 parts
4G GNSS-RTK High Precision Positioning Kit (EMEA & Thailand, GPS / GLONASS / Galileo / BDS / QZSS) visual preview
50 Channel GS407 Helical GPS Receiver visual preview
5G/4G/3G/GNSS External Antenna, SMA to IPEX-4 visual preview
A9G GSM/GPRS+GPS Module visual previewAdafruit Ultimate GPS (PA1616S/PA1616D), NEO-6M and NEO-M9N u-blox breakouts, Gravity GNSS BeiDou boards with I2C/UART, and 4G or LoRa RTK kits — accuracy and constellation requirements split them.
Wireless & comms · GNSS & GPS · 67 parts
2mm 10-Pin XBee Header visual preview
2mm 10-Pin XBee Socket - SMD visual preview
2mm 10pin XBee Socket visual preview
315MHz ASK/OOK Transmitter Module visual previewRFM95W and SX1262 LoRa transceivers, Wio-E5 LoRaWAN modules, SX1302 gateways, Digi XBee mesh radios, 433 MHz ASK serial links, Dragino IoT sensor nodes, and the SDRplay RSP2 wideband SDR receiver.
Wireless & comms · LoRa & RF modules · 95 parts
SPI chip select; pull down when transmitting to or from the ATWINC. Pulled to VIN with 100 kΩ by default. Source: Adafruit Learn pinouts.
Module enable; tie to 3-5 V to keep module on, or to ground to disable. Pulled low with 100 kΩ by default. Source: Adafruit Learn pinouts.
Interrupt output from the module to a microcontroller interrupt input. Source: Adafruit Learn pinouts.
Module reset; pull high to bring the module out of reset. Pulled low with 100 kΩ by default. Source: Adafruit Learn pinouts.
Wake input signal for waking the module. Source: Adafruit Learn pinouts.
Selects SPI default or UART data transport; Adafruit says to keep disconnected for normal SPI use. Source: Adafruit Learn pinouts.
UART receive/data transport pin; Adafruit notes UART code is not provided and to keep disconnected for normal use. Source: Adafruit Learn pinouts.
UART transmit/data transport pin; Adafruit notes UART code is not provided and to keep disconnected for normal use. Source: Adafruit Learn pinouts.
| Pin | Position | Type | Function | Voltage |
|---|---|---|---|---|
| VIN | power | Power input for the ATWINC1500 breakout. Source: Adafruit Learn pinouts. | 3.3-5.5 VDC; module can draw up to 300 mA during transmit. | |
| GND | ground | Ground for signal and power. Source: Adafruit Learn pinouts. | 0 V | |
| SCK | spi | SPI clock input. Source: Adafruit Learn pinouts. | 3 V or 5 V compliant. | |
| MISO | spi | SPI data output from module. Source: Adafruit Learn pinouts. | 3.3 V logic level. | |
| MOSI | spi | SPI data input to module. Source: Adafruit Learn pinouts. | 3 V or 5 V compliant. | |
| CS | spi | SPI chip select; pull down when transmitting to or from the ATWINC. Pulled to VIN with 100 kΩ by default. Source: Adafruit Learn pinouts. | ||
| EN | control | Module enable; tie to 3-5 V to keep module on, or to ground to disable. Pulled low with 100 kΩ by default. Source: Adafruit Learn pinouts. | 3-5 V enable signal. | |
| IRQ | interrupt | Interrupt output from the module to a microcontroller interrupt input. Source: Adafruit Learn pinouts. | 3.3 V logic level. | |
| RST | reset | Module reset; pull high to bring the module out of reset. Pulled low with 100 kΩ by default. Source: Adafruit Learn pinouts. | ||
| WAKE | control | Wake input signal for waking the module. Source: Adafruit Learn pinouts. | 3-5 V logic input. | |
| CFG | configuration | Selects SPI default or UART data transport; Adafruit says to keep disconnected for normal SPI use. Source: Adafruit Learn pinouts. | ||
| RXD | uart | UART receive/data transport pin; Adafruit notes UART code is not provided and to keep disconnected for normal use. Source: Adafruit Learn pinouts. | ||
| TXD | uart | UART transmit/data transport pin; Adafruit notes UART code is not provided and to keep disconnected for normal use. Source: Adafruit Learn pinouts. |
XBee USB Adapter V2 - Atmega8U2
XBee-socket USB adapter using an Atmega8U2 USB-to-serial converter, Micro USB and X-CTU-compatible configuration path. Good for configuring or using XBee-style modules from a computer.