
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference, as well as calculations to handle any non-linearities. For a long time we've suggested our MAX31855K breakout, which works great but is only for K-type thermocouples.
Power input for the breakout. Adafruit Learn says the onboard regulator accepts 3-5VDC and to power it at the microcontroller logic level.
3.3V regulator output available from the breakout.
Common ground for power and logic.
SPI clock input to the MAX31856 breakout.
SPI data out from the MAX31856 to the microcontroller, MISO.
SPI · I2S · 3-5VDC input, same as logic level on Vin · 3.3V output, up to 100mA per Adafruit Learn
Verify supply voltage and logic levels before powering up.
Module pins: Vin, 3Vo, GND, SCK, SDO, SDI, CS, FLT. Schematik maps them to your board in the app.
SparkFun Qwiic Pro Micro BoogieBoard visual preview
9V to Barrel Jack Adapter visual preview
SparkFun 16x2 SerLCD - RGB Backlight (Qwiic) visual preview
MicroUSB Plug to 5.5/2.1mm DC Barrel Jack Adapter | Kiwi Electronics visual previewSort passive connector adapters from Qwiic boards, LCD modules and microSD card adapters before assuming anything with the right plug will substitute safely.
Connectors & cables · Connectors · 28 parts
RGB backlight positive LCD 16x2 visual preview
SparkFun 16x2 SerLCD - RGB Backlight (Qwiic) visual preview
I2C 20x4 Arduino LCD Display Module visual preview
Gravity: I2C 16x2 Arduino LCD with RGB Backlight Display V2.0 visual previewCharacter LCDs, SPI TFTs, e-paper modules and larger capacitive-touch TFT panels solve different display jobs. Treat display class, interface, controller, resolution, touch, refresh behaviour, storage, voltage and mounting as separate swap checks.
Displays · TFT & LCD displays · 35 parts
MQ-2 Gas Sensor visual preview
MQ-3 Gas Sensor visual preview
MQ-135 Gas Sensor visual preview
Grove - Air quality sensor visual previewChoose between MQ gas sensors, VOC/eCO2 indoor-air sensors, true CO2 modules and particulate sensors without treating every air-quality breakout as the same detector.
Sensors · Gas & air-quality sensors · 31 parts
Raspberry Pi Pico visual preview
Adafruit Feather nRF52840 Express visual preview
Pan-Tilt HAT kit visual previewESP32, Arduino Uno, Raspberry Pi Pico, and compatible add-on boards for running builds.
Boards · Microcontroller boards · 25 parts
SPI data in to the MAX31856 from the microcontroller, MOSI.
SPI chip select input, driven low to start an SPI transaction.
Fault output. Adafruit Learn says it goes low when there is a MAX31856 fault.
Data-ready output for advanced use, goes low after a requested reading is ready.
| Pin | Position | Type | Function | Voltage |
|---|---|---|---|---|
| Vin | power | Power input for the breakout. Adafruit Learn says the onboard regulator accepts 3-5VDC and to power it at the microcontroller logic level. | 3-5VDC input, same as logic level on Vin | |
| 3Vo | power | 3.3V regulator output available from the breakout. | 3.3V output, up to 100mA per Adafruit Learn | |
| GND | ground | Common ground for power and logic. | 0V | |
| SCK | signal | SPI clock input to the MAX31856 breakout. | 3-5V logic safe, use the logic level on Vin | |
| SDO | signal | SPI data out from the MAX31856 to the microcontroller, MISO. | 3-5V logic safe, use the logic level on Vin | |
| SDI | signal | SPI data in to the MAX31856 from the microcontroller, MOSI. | 3-5V logic safe, use the logic level on Vin | |
| CS | signal | SPI chip select input, driven low to start an SPI transaction. | 3-5V logic safe, use the logic level on Vin | |
| FLT | signal | Fault output. Adafruit Learn says it goes low when there is a MAX31856 fault. | ||
| DRDY | signal | Data-ready output for advanced use, goes low after a requested reading is ready. |