Adafruit STEMMA Non-Latching Mini Relay - JST PH 2mm

Non-latching mini relay breakout with JST PH 2 mm connector for solderless microcontroller wiring, switching loads up to 250 V AC or DC. Controlled by any 3.3 V or 5 V digital output; suitable for lamps, fans, and solenoids.

VCC
STEMMA/JST PH red power wire for the relay board input; source states it works with any 3V or 5V microcontroller and uses about 50mA when active.
Type · powerVoltage · 3V or 5V logic supply, source-stated
GND
STEMMA/JST PH ground return for the relay board input.
Type · groundVoltage · 0V
Signal
STEMMA/JST PH white signal wire. Pulling Signal high switches the relay so COM connects to NO and NC disconnects.
Type · digitalVoltage · 3V or 5V logic compatible, source-stated
COM
Relay common contact. Source states COM is normally mechanically connected to NC and switches to NO when Signal is high.
Type · relay contactVoltage · Switching contact, source states up to 2A at 30VDC or about 40VAC or lower, lower current at higher voltages.
NC
Normally closed relay contact. Source states COM is connected to NC when the relay is not active and NC disconnects when Signal is high.

Relays

43 other options

Gravity and Grove single-relay modules, Pi relay HATs, USB-RLY16 boards, Sonoff Wi-Fi smart switches, and Waveshare Modbus RTU/TCP industrial modules — matched by control interface and contact rating.

View all 43

16-Ch Ethernet Relay Module, Modbus RTU / Modbus TCP Protocol, Ethernet Port Communication, Supports PoE Power Supply, With Various Isolation And Protection Circuits visual preview

Related groups

4 groups

LED pixels

WS2812/SK6812 NeoPixel strips, rings and Jewels, APA102 DotStar pixels, and plain analog RGB strips — each matched to its protocol and host, not just its connector.

Components · Addressable LEDs · 176 parts

Bare ICs

74HC logic gates, MCP3008/MCP23017 ADCs and expanders, 24LC256 EEPROM, 4N25-series optocouplers and ULN2803A drivers — bare DIP chips with no breakout-board conveniences like pull-ups or level shifting.

Components · Integrated circuits · 68 parts

Converters

ADS1115/MCP3421 ADCs, MCP4725 and GP8413 DACs, CP2102 USB-UART boards, and I2C plumbing like the LTC4316 address shifter — matched to bus, resolution and signal range.

Components · Interface converters · 115 parts

Memory

24LC32/25LC256 EEPROM, I2C FRAM, 64Mbit PSRAM, and microSD breakouts up to 64GB — matched to write frequency and data volume, not just interface.

Components · Memory & storage · 39 parts

Pin	Type	Function	Voltage
VCC	power	STEMMA/JST PH red power wire for the relay board input; source states it works with any 3V or 5V microcontroller and uses about 50mA when active.	3V or 5V logic supply, source-stated
GND	ground	STEMMA/JST PH ground return for the relay board input.	0V
Signal	digital	STEMMA/JST PH white signal wire. Pulling Signal high switches the relay so COM connects to NO and NC disconnects.	3V or 5V logic compatible, source-stated
COM	relay contact	Relay common contact. Source states COM is normally mechanically connected to NC and switches to NO when Signal is high.	Switching contact, source states up to 2A at 30VDC or about 40VAC or lower, lower current at higher voltages.
NC	relay contact	Normally closed relay contact. Source states COM is connected to NC when the relay is not active and NC disconnects when Signal is high.	Switching contact, source-stated ratings apply.
NO	relay contact	Normally open relay contact. Source states NO is disconnected normally and connects to COM when Signal is high.	Switching contact, source-stated ratings apply.

Pinout

LED pixels

Bare ICs

Converters

Memory