Build Season 2026 is live: Publish a build to win M5Stack hardwareBuild Season 2026 is live

Adafruit 2.13" Monochrome eInk / ePaper Display FeatherWing - 250x122

Adafruit 2.13" Monochrome eInk / ePaper Display FeatherWing - 250x122 — Adafruit — adafruit-2-13-monochrome-eink-epaper-display-featherwing-250x122-monochrome

250x122 monochrome e-paper FeatherWing for any Feather board. Bistable display retains image without power; slow refresh rate limits use to infrequently updated content.

Pinout

Logical pinout · physical placement not verified
ADAFRUIT 2.13" MONOCHRMOSIEINK CSMISOEINK DCSCKRESETSD CSBUSYSRAM CS
  • MOSIFeather SPI

    FeatherWing SPI MOSI pad, sends data from the controller to SD card, SRAM, and eInk display per Adafruit Learn pinouts

    Type · SPI
  • MISOFeather SPI

    FeatherWing SPI MISO pad, used by the SD card and SRAM; eInk display itself is write-only per Adafruit Learn pinouts

    Type · SPI
  • SCKFeather SPI

    FeatherWing SPI clock input, required for eInk display, SRAM, and SD card per Adafruit Learn pinouts

    Type · SPI
  • SD CSafter I2C pins, first chip-select pad

    SD card chip-select; Adafruit maps this FeatherWing signal to Feather pin D5 on common Feather boards

    Type · GPIO
  • SRAM CSafter I2C pins, second chip-select pad

    SRAM chip-select for the onboard RAM; Adafruit maps this FeatherWing signal to Feather pin D6 on common Feather boards

    Type · GPIO
  • EINK CSafter I2C pins, third chip-select pad

    eInk display chip-select; Adafruit maps this FeatherWing signal to Feather pin D9 on common Feather boards

    Type · GPIO
  • EINK DCafter I2C pins, data/command pad

    eInk display data/command control; Adafruit maps this FeatherWing signal to Feather pin D10 on common Feather boards

    Type · GPIO
  • RESETFeather reset

    eInk reset is tied to an auto-reset circuit and the Feather reset pin per Adafruit Learn pinouts

    Type · Control
  • BUSYbusy breakout pad

    eInk busy-detect signal available on a breakout pad; optional if firmware uses fixed delays per Adafruit Learn pinouts

    Type · GPIO

Start wiring

SPI · I2C · 3.3 V · Bare

Verify supply voltage and logic levels before powering up.

Module pins: MOSI, MISO, SCK. Schematik maps them to your board in the app.

E-paper

100 other options

Waveshare makes up the large majority of parts here and often sells the same panel twice: once as a raw display needing a separate driver board, and once as a module or HAT+ with the SPI controller attached.

View all 100

Related groups

4 groups

TFT & LCD

16×2 and 20×4 character LCDs (parallel, I2C backpack, Qwiic, Grove), SPI TFTs from 0.71 to 3.5 inches, and large DSI and HDMI capacitive-touch panels up to 13.3 inches.

Displays · TFT & LCD displays · 190 parts

LED displays

Adafruit HT16K33 backpacks, MAX7219 daisy-chains, NeoPixel and DotStar grids, HUB75 RGB matrix panels, charlieplexed arrays, bare clock displays, and two VFD character modules — almost 90 parts, none wired the same way.

Displays · LED displays · 89 parts

OLED

About 30 parts: monochrome I2C modules from 0.49 to 1.3 inches, SPI/I2C grayscale and 65K-color RGB panels up to 1.5 inches, a transparent OLED, and ecosystem-specific units for Raspberry Pi, FireBeetle and M5Stack Grove.

Displays · OLED displays · 30 parts

3D printing

DFRobot 1.75 mm PLA in 1 kg spools makes up the bulk of the group, in over 15 colors. Specialty options include PVA in both diameters, NinjaFlex flexible filament, Proto-Pasta conductive PLA, and wood-fill. OverLord printer spares and OverLord printers round out the hardware side.

Tools & prototyping · 3D printing · 53 parts