
Rigid PCB bar carrying 128 APA102 DotStar LEDs in a high-density layout, controlled via 2-wire SPI-compatible daisy-chain with high refresh rates. Compatible with any microcontroller or SPI peripheral.
Ground connection for the DotStar LED bar power and signal reference. Adafruit DotStar guide identifies ground/GND as one of the four labelled strip connections.
5 V DC power input for the LED bar. Product page states the bar has GND and 5V wires and operating voltage DC5V; DotStar guide identifies 5V as the strip power pin.
DotStar data input at the originating end of the bar. Adafruit DotStar guide says the data line is usually labelled D or DI and connects to the microcontroller data pin.
DotStar clock input at the originating end of the bar. Adafruit DotStar guide says the clock line is usually labelled C or CI and connects to the microcontroller clock pin.
WS2812/SK6812 NeoPixel strips, rings and Jewels, APA102 DotStar pixels, and plain analog RGB strips — each matched to its protocol and host, not just its connector.
18-Channel 8-bit PWM LED Driver w/ I2C Interface visual preview
24LC256 I/P I2C EEPROM PDIP-8 visual preview
24LC256 P DIP-8 visual preview
4N25 DIP-6 visual preview74HC logic gates, MCP3008/MCP23017 ADCs and expanders, 24LC256 EEPROM, 4N25-series optocouplers and ULN2803A drivers — bare DIP chips with no breakout-board conveniences like pull-ups or level shifting.
Components · Integrated circuits · 68 parts
10-bit ADC (SPI) visual preview
2-Channel RS232 Module for Raspberry Pi Pico visual preview
4-Ch USB 3.2 Gen1 Hub (USB3.2-Gen1-HUB-4U) visual preview
6-in-1 USB to Serial Converter visual previewADS1115/MCP3421 ADCs, MCP4725 and GP8413 DACs, CP2102 USB-UART boards, and I2C plumbing like the LTC4316 address shifter — matched to bus, resolution and signal range.
Components · Interface converters · 115 parts
256MB Micro SD Memory Card visual preview
25LC256 256 Kbit SPI EEPROM visual preview
64 Mbit Serial Pseudo SRAM - PSRAM - 3.3V 133 MHz visual preview
8GB Class 10 SD/MicroSD Memory Card - SD Adapter Included visual preview24LC32/25LC256 EEPROM, I2C FRAM, 64Mbit PSRAM, and microSD breakouts up to 64GB — matched to write frequency and data volume, not just interface.
Components · Memory & storage · 39 parts
1/4W Resistor Pack - 400 PCS visual preview
1N4001 Diode - 10 pack visual preview
1N4007 Diode visual preview
1N4148 General Purpose Fast Switching Diode visual previewE12 resistor kits, ceramic and electrolytic capacitor sets, 1N4148/1N4007 diodes, TIP120 Darlingtons, IRLZ44N MOSFETs and 100F supercapacitors — bench stock in kit quantities.
Components · Passives · 56 parts
| Pin | Position | Type | Function | Voltage |
|---|
| GND | ground | Ground connection for the DotStar LED bar power and signal reference. Adafruit DotStar guide identifies ground/GND as one of the four labelled strip connections. | ||
| 5V | power | 5 V DC power input for the LED bar. Product page states the bar has GND and 5V wires and operating voltage DC5V; DotStar guide identifies 5V as the strip power pin. | 5V DC; product page recommends keeping power under 15W / 3A at 5V for this bar. | |
| D / DI | signal | DotStar data input at the originating end of the bar. Adafruit DotStar guide says the data line is usually labelled D or DI and connects to the microcontroller data pin. | ||
| C / CI | signal | DotStar clock input at the originating end of the bar. Adafruit DotStar guide says the clock line is usually labelled C or CI and connects to the microcontroller clock pin. |
Flora RGB Smart NeoPixel version 2 - Pack of 4