Adafruit NeoPixel LED Outdoor Netting - 20x20 LEDs - 1x1 Meter

400-LED (20×20) outdoor-rated NeoPixel netting, 1×1 m, driven from a single data pin via WS2812B protocol. Weatherproof construction removes the need to assemble multiple strips for large grid displays.

+5V
NeoPixel net positive power input. Product page identifies the item as SK6812/WS2812/NeoPixel LEDs; Adafruit NeoPixel guide states extra/input wires correspond to +5V, ground and data, and that 5V DC power is the normal supply.
Type · powerVoltage · 5V DC typical for NeoPixel power; product page states 5V logic-level data for this netting.
GND
Common ground / negative power return. Adafruit guide says ground must be connected before anything else and shared with the controller/power supply.
Type · groundVoltage · 0V reference
DIN / DI
Data input at the input end of the NeoPixel net. Product page states the net accepts classic SK6812/WS2812/NeoPixel data at 5V logic level; Adafruit guide says the input end is labelled DIN or DI and data moves in one direction.
Type · signalVoltage · 5V logic level stated on the product page; 3.3V may work per product wording but is not guaranteed.
DOUT / DO
Data output at the far end of a NeoPixel chain for chaining additional pixels; Adafruit guide says DOUT/DO can be left disconnected or connected to the next chain data input.
Type · signalVoltage · NeoPixel chain data output, logic follows powered pixel chain.

LED pixels

175 other options

WS2812/SK6812 NeoPixel strips, rings and Jewels, APA102 DotStar pixels, and plain analog RGB strips — each matched to its protocol and host, not just its connector.

View all 175

Flora RGB Smart NeoPixel version 2 - Pack of 4 visual preview

Related groups

4 groups

Bare ICs

74HC logic gates, MCP3008/MCP23017 ADCs and expanders, 24LC256 EEPROM, 4N25-series optocouplers and ULN2803A drivers — bare DIP chips with no breakout-board conveniences like pull-ups or level shifting.

Components · Integrated circuits · 68 parts

Converters

ADS1115/MCP3421 ADCs, MCP4725 and GP8413 DACs, CP2102 USB-UART boards, and I2C plumbing like the LTC4316 address shifter — matched to bus, resolution and signal range.

Components · Interface converters · 115 parts

Memory

24LC32/25LC256 EEPROM, I2C FRAM, 64Mbit PSRAM, and microSD breakouts up to 64GB — matched to write frequency and data volume, not just interface.

Components · Memory & storage · 39 parts

Passives

E12 resistor kits, ceramic and electrolytic capacitor sets, 1N4148/1N4007 diodes, TIP120 Darlingtons, IRLZ44N MOSFETs and 100F supercapacitors — bench stock in kit quantities.

Components · Passives · 56 parts

Pin	Type	Function	Voltage
+5V	power	NeoPixel net positive power input. Product page identifies the item as SK6812/WS2812/NeoPixel LEDs; Adafruit NeoPixel guide states extra/input wires correspond to +5V, ground and data, and that 5V DC power is the normal supply.	5V DC typical for NeoPixel power; product page states 5V logic-level data for this netting.
GND	ground	Common ground / negative power return. Adafruit guide says ground must be connected before anything else and shared with the controller/power supply.	0V reference
DIN / DI	signal	Data input at the input end of the NeoPixel net. Product page states the net accepts classic SK6812/WS2812/NeoPixel data at 5V logic level; Adafruit guide says the input end is labelled DIN or DI and data moves in one direction.	5V logic level stated on the product page; 3.3V may work per product wording but is not guaranteed.
DOUT / DO	signal	Data output at the far end of a NeoPixel chain for chaining additional pixels; Adafruit guide says DOUT/DO can be left disconnected or connected to the next chain data input.	NeoPixel chain data output, logic follows powered pixel chain.

Pinout

Bare ICs

Converters

Memory

Passives