Gravity: CAT4 SIM7600G-H Global 4G & GNSS Module (TEL0162)

4G CAT4 LTE module with integrated GNSS supporting up to 150 Mbps downlink and 50 Mbps uplink, communicates via UART AT commands. Faster downlink than the CAT1 TEL0161 sibling. Compatible with Arduino, Raspberry Pi, and LattePanda.

Logical pinout · physical placement not verified

MAINOfficial table 2 row 1
The primary antenna interface, connects to GSM antenna
Type · Analog
AUXOfficial table 2 row 2
The auxiliary antenna interface, also connects to GSM antenna
Type · GPIO
GNSSOfficial table 2 row 3
Connects to the GPS positioning antenna
Type · GPIO
UARTOfficial table 2 row 4
UART interface (interface voltage level 3.3V-5V)
Type · UART
USB-Type COfficial table 2 row 5
USB device interface, used for communication and parameter configuration with a computer
Type · GPIO
Power INOfficial table 2 row 6
External power supply required when using the UART interface (5V-12V)
Type · Power
Audio OUTOfficial table 2 row 7
External 8Ω 1.0W speaker
Type · GPIO
SIM CardOfficial table 2 row 8
Insert a SIM card
Type · Unknown

Pin	Position	Type	Function
MAIN	Official table 2 row 1	Analog	The primary antenna interface, connects to GSM antenna
AUX	Official table 2 row 2	GPIO	The auxiliary antenna interface, also connects to GSM antenna
GNSS	Official table 2 row 3	GPIO	Connects to the GPS positioning antenna
UART	Official table 2 row 4	UART	UART interface (interface voltage level 3.3V-5V)
USB-Type C	Official table 2 row 5	GPIO	USB device interface, used for communication and parameter configuration with a computer
Power IN	Official table 2 row 6	Power	External power supply required when using the UART interface (5V-12V)
Audio OUT	Official table 2 row 7	GPIO	External 8Ω 1.0W speaker
SIM Card	Official table 2 row 8	Unknown	Insert a SIM card

Logical pinout · physical placement not verified

Pin details

8 connections

MAIN
The primary antenna interface, connects to GSM antenna
Analog
Official table 2 row 1
AUX
The auxiliary antenna interface, also connects to GSM antenna
GPIO
Official table 2 row 2
GNSS
Connects to the GPS positioning antenna
GPIO
Official table 2 row 3
UART
UART interface (interface voltage level 3.3V-5V)
UART
Official table 2 row 4
USB-Type C
USB device interface, used for communication and parameter configuration with a computer
GPIO
Official table 2 row 5
Power IN
External power supply required when using the UART interface (5V-12V)
Power
Official table 2 row 6
Audio OUT
External 8Ω 1.0W speaker
GPIO
Official table 2 row 7
SIM Card
Insert a SIM card
Unknown
Official table 2 row 8

Start wiring

UART · USB · Breakout

Confirm the data interface matches your host board.

Module pins: UART, Power IN, MAIN. Schematik maps them to your board in the app.

Cellular

57 other options

Adafruit FONA GSM breakouts, the Gravity Air780EU 4G Cat 1 module, Dragino NB-IoT Shield-B8, Pycom FiPy, Quectel and SIMCom M.2 5G modems, and the RockBLOCK 9603 Iridium modem each target a different network tier.

View all 57

Related groups

4 groups

Bluetooth

BLE 5-era modules (nRF52840, MDBT50Q), XIAO MG24 boards with Matter-over-Thread, Bluefruit UART/SPI bridges, HM-11 serial modules, and BLE sniffers cover different jobs and different hosts.

Wireless & comms · Bluetooth modules · 71 parts

GNSS & GPS

Adafruit Ultimate GPS (PA1616S/PA1616D), NEO-6M and NEO-M9N u-blox breakouts, Gravity GNSS BeiDou boards with I2C/UART, and 4G or LoRa RTK kits — accuracy and constellation requirements split them.

Wireless & comms · GNSS & GPS · 68 parts

LoRa & RF

RFM95W and SX1262 LoRa transceivers, Wio-E5 LoRaWAN modules, SX1302 gateways, Digi XBee mesh radios, 433 MHz ASK serial links, Dragino IoT sensor nodes, and the SDRplay RSP2 wideband SDR receiver.

Wireless & comms · LoRa & RF modules · 94 parts

Networking

ESP8285, ATWINC1500, and EMW3060 Wi-Fi modules; the WIZ5500 Ethernet co-processor; the DP83848 RMII PHY board; 802.11n USB adapters for the Pi; and an XBee USB configuration adapter.

Wireless & comms · Wi-Fi & networking · 26 parts