Logical pinout · physical placement not verified

Pin 1GND1
Ground connection. Adafruit product page says to connect pin #1 to ground.
Type · GroundVoltage · 0V
Pin 2on-time set2
On-time delay setting input. Adafruit says connect pin #2 to ground for an on time of 2 seconds, or use a resistor divider to set delay time.
Type · ControlVoltage · 0V to 3.3V delay-setting input per Adafruit product page
Pin 33.3V3
3.3V power input. Adafruit product page says to connect pin #3 to 3.3V and run the sensor on 3.3V power.
Type · PowerVoltage · 3.3V
Pin 4signal4
Digital PIR motion signal output. Adafruit says to check signal on pin #4 and describes the digital output as 3.3V high/low.
Type · SignalVoltage · 3.3V logic high/low output per Adafruit product page

Pin	Position	Type	Function	Voltage
Pin 1GND	1	Ground	Ground connection. Adafruit product page says to connect pin #1 to ground.	0V
Pin 2on-time set	2	Control	On-time delay setting input. Adafruit says connect pin #2 to ground for an on time of 2 seconds, or use a resistor divider to set delay time.	0V to 3.3V delay-setting input per Adafruit product page
Pin 33.3V	3	Power	3.3V power input. Adafruit product page says to connect pin #3 to 3.3V and run the sensor on 3.3V power.	3.3V
Pin 4signal	4	Signal	Digital PIR motion signal output. Adafruit says to check signal on pin #4 and describes the digital output as 3.3V high/low.	3.3V logic high/low output per Adafruit product page

Logical pinout · physical placement not verified

Pin details

4 connections

Pin 1GND
Ground connection. Adafruit product page says to connect pin #1 to ground.
GroundVoltage · 0V
1
Pin 2on-time set
On-time delay setting input. Adafruit says connect pin #2 to ground for an on time of 2 seconds, or use a resistor divider to set delay time.
ControlVoltage · 0V to 3.3V delay-setting input per Adafruit product page
2
Pin 33.3V
3.3V power input. Adafruit product page says to connect pin #3 to 3.3V and run the sensor on 3.3V power.
PowerVoltage · 3.3V
3
Pin 4signal
Digital PIR motion signal output. Adafruit says to check signal on pin #4 and describes the digital output as 3.3V high/low.
SignalVoltage · 3.3V logic high/low output per Adafruit product page
4

Start wiring

Analog · I2C · UART · 3.3 – 5 V · Breakout

Verify supply voltage and logic levels before powering up.

Module pins: Pin 3 / 3.3V, Pin 1 / GND, Pin 4 / signal. Schematik maps them to your board in the app.

Other sensors

62 other options

PIR and mmWave presence sensors, Hall-effect and angle encoders, piezo vibration discs, gesture breakouts and more — grouped here because they fit nowhere else.

View all 62

Related groups

4 groups

Biometrics

UART/I2C fingerprint modules, MAX30102 PPG breakouts, and analog ECG/EMG front-ends for access control and hobby biometric sensing.

Sensors · Biometric sensors · 26 parts

Cameras

Pi CSI modules, USB cameras, MCU-class OV2640/OV5640 boards, on-camera AI like HuskyLens and OpenMV, and thermal or ToF imagers — over 130 listings across very different pipelines.

Sensors · Cameras & vision · 141 parts

Power monitors

INA-series I2C monitors, Hall-effect sensors like the ACS723 and Gravity 20A/50A boards, and non-invasive CT clamps for everything from 3.3V rail telemetry to mains current sensing.

Sensors · Current & voltage · 25 parts

Distance sensors

About 180 listings spanning VL53-series ToF breakouts, HC-SR04 and MaxSonar ultrasonics, 360° triangulation LiDARs, IR proximity sensors, 24GHz mmWave presence detection and laser break-beam sensors.

Sensors · Distance sensors · 177 parts