Vin
Board power input. Adafruit Learn states the chip can use 2.5-5VDC and the board should be powered at the same level as the microcontroller logic.
Type · powerVoltage · 2.5-5VDC, match controller logic level
GND
Common ground for power and logic.
Type · groundVoltage · 0V
SCL
I2C clock line. Adafruit Learn states this pin has a 10K pull-up resistor to Vin.
Type · i2c clockVoltage · logic level pulled up to Vin
SDA
I2C data line. Adafruit Learn states this pin has a 10K pull-up resistor to Vin.
Type · i2c dataVoltage · logic level pulled up to Vin
STEMMA QT
STEMMA QT I2C connector for development boards and accessories, carrying the board I2C/power connection.
Type · connector

Start wiring

I2C · SPI · Single data line · 3.3 – 5 V · Breakout

Confirm the data interface matches your host board.

Module pins: Vin, GND, SCL, SDA. Schematik maps them to your board in the app.

Temp & humidity

165 other options

DHT/AHT sensors, SHT-series humidity chips, BMP and LPS barometers, BME combined sensors, DS18B20 probes, thermocouple amplifiers and non-contact MLX IR sensors — about 165 listings, very different accuracy classes.

View all 165

Gravity: Analog LM35 Temperature Sensor For Arduino visual preview

Related groups

4 groups

Biometrics

UART/I2C fingerprint modules, MAX30102 PPG breakouts, and analog ECG/EMG front-ends for access control and hobby biometric sensing.

Sensors · Biometric sensors · 24 parts

Cameras

Pi CSI modules, USB cameras, MCU-class OV2640/OV5640 boards, on-camera AI like HuskyLens and OpenMV, and thermal or ToF imagers — over 130 listings across very different pipelines.

Sensors · Cameras & vision · 139 parts

Power monitors

INA-series I2C monitors, Hall-effect sensors like the ACS723 and Gravity 20A/50A boards, and non-invasive CT clamps for everything from 3.3V rail telemetry to mains current sensing.

Sensors · Current & voltage · 24 parts

Distance sensors

About 180 listings spanning VL53-series ToF breakouts, HC-SR04 and MaxSonar ultrasonics, 360° triangulation LiDARs, IR proximity sensors, 24GHz mmWave presence detection and laser break-beam sensors.

Sensors · Distance sensors · 178 parts

Pin	Type	Function	Voltage
Vin	power	Board power input. Adafruit Learn states the chip can use 2.5-5VDC and the board should be powered at the same level as the microcontroller logic.	2.5-5VDC, match controller logic level
GND	ground	Common ground for power and logic.	0V
SCL	i2c clock	I2C clock line. Adafruit Learn states this pin has a 10K pull-up resistor to Vin.	logic level pulled up to Vin
SDA	i2c data	I2C data line. Adafruit Learn states this pin has a 10K pull-up resistor to Vin.	logic level pulled up to Vin
STEMMA QT	connector	STEMMA QT I2C connector for development boards and accessories, carrying the board I2C/power connection.
ADR	address select	I2C address selection. Adafruit Learn states the default address is 0x44 via 10K pull-down, and tying ADR to Vin selects 0x45.	low default, tie to Vin for address 0x45
RST	reset	Hardware reset input. Adafruit Learn states it has a 10K pull-up and can be connected to ground for reset.	pulled up by default, active low reset
ALR	interrupt	Alert/interrupt output for configured sensor events.

Pinout

Start wiring

Biometrics

Cameras

Power monitors

Distance sensors