Board power input. Adafruit states the onboard regulator takes 3-5VDC and converts it down for the BMP3xx sensor.
3.3V output from the onboard voltage regulator, available for small external loads.
Common ground for power and logic.
SPI clock input, also I2C clock when using I2C mode. Adafruit states breakout inputs are 3-5V logic-level safe.
SPI serial data out / MISO from the BMP3xx to the controller.
I2C · SPI · Single data line · 3.3 – 5 V · Breakout
Confirm the data interface matches your host board.
Module pins: VIN, 3Vo, GND, SCK / SCL, SDO, SDA / SDI, CS, INT. Schematik maps them to your board in the app.
DHT/AHT sensors, SHT-series humidity chips, BMP and LPS barometers, BME combined sensors, DS18B20 probes, thermocouple amplifiers and non-contact MLX IR sensors — about 165 listings, very different accuracy classes.
Biomedical Sensor Pad (10 pack) visual preview
BOSON: Heart Rate Monitor Sensor i20 visual preview
Capacitive Fingerprint Reader visual preview
Capacitive Fingerprint Reader (B) visual previewUART/I2C fingerprint modules, MAX30102 PPG breakouts, and analog ECG/EMG front-ends for access control and hobby biometric sensing.
Sensors · Biometric sensors · 24 parts
0.3M Pixel Serial JPEG Camera Module visual preview
100X Industrial Microscope Lens for Raspberry Pi HQ Camera visual preview
12.3MP Camera Module for NVIDIA Jetson Nano & Raspberry Pi CM3 visual preview
2.4G Wireless Video Transmission Module (640*480 Resolution) visual previewPi CSI modules, USB cameras, MCU-class OV2640/OV5640 boards, on-camera AI like HuskyLens and OpenMV, and thermal or ToF imagers — over 130 listings across very different pipelines.
Sensors · Cameras & vision · 139 parts
0.28 Inch LED Digital DC Voltmeter - Green visual preview
4-ch Current/Voltage/Power Monitor HAT visual preview
Adafruit INA219 FeatherWing visual preview
Adafruit INA219 High Side DC Current Sensor Breakout STEMMA QT visual previewINA-series I2C monitors, Hall-effect sensors like the ACS723 and Gravity 20A/50A boards, and non-invasive CT clamps for everything from 3.3V rail telemetry to mains current sensing.
Sensors · Current & voltage · 24 parts
VL53L1X Time of Flight (ToF) Sensor Breakout visual preview
Solid State TOF LiDAR - CE30-A visual preview
25m Long Distance ToF Laser Sensor (±3cm Accuracy, 100Hz, 100K LUX Resistant) visual preview
4-20HR-MaxSonar-WRMI MB7489 Waterproof Ultrasonic Distance Sensor (50~500cm, IP67) visual previewAbout 180 listings spanning VL53-series ToF breakouts, HC-SR04 and MaxSonar ultrasonics, 360° triangulation LiDARs, IR proximity sensors, 24GHz mmWave presence detection and laser break-beam sensors.
Sensors · Distance sensors · 178 parts
High-precision Bosch BMP388 barometric pressure and temperature sensor breakout, selectable I2C or SPI. Improved accuracy over BMP280 makes it well-suited for precision altimetry in drones and environmental monitoring.
I2C data line, also SPI serial data in / MOSI to the BMP3xx.
SPI chip-select input, pulled low to start an SPI transaction.
Interrupt output from the BMP3xx for data-ready signalling.
| Pin | Position | Type | Function | Voltage |
|---|---|---|---|---|
| VIN | power | Board power input. Adafruit states the onboard regulator takes 3-5VDC and converts it down for the BMP3xx sensor. | 3-5V DC input | |
| 3Vo | power | 3.3V output from the onboard voltage regulator, available for small external loads. | 3.3V output, up to 100mA per Adafruit guide | |
| GND | ground | Common ground for power and logic. | 0V | |
| SCK / SCL | signal | SPI clock input, also I2C clock when using I2C mode. Adafruit states breakout inputs are 3-5V logic-level safe. | 3-5V logic input | |
| SDO | signal | SPI serial data out / MISO from the BMP3xx to the controller. | 3.3V logic output, readable by 5V microcontrollers | |
| SDA / SDI | signal | I2C data line, also SPI serial data in / MOSI to the BMP3xx. | 3-5V logic input | |
| CS | signal | SPI chip-select input, pulled low to start an SPI transaction. | 3-5V logic input | |
| INT | signal | Interrupt output from the BMP3xx for data-ready signalling. | 3.3V logic output, readable by 5V microcontrollers |
Gravity: Analog LM35 Temperature Sensor For Arduino
Analog temperature-only module. Useful when humidity is not needed and the controller has an ADC input.