LPS33HW Water Resistant Pressure Sensor - STEMMA QT

Water-resistant pressure sensor breakout (LPS33HW) with STEMMA QT/Qwiic connectors, supporting I2C or SPI and both absolute and relative pressure in caustic or damp environments. Arduino SPI support only; CircuitPython and Raspberry Pi use I2C.

VIN
Power input for the breakout; Adafruit states the onboard regulator accepts 3-5VDC and converts it to 3.3V for the sensor.
Type · powerVoltage · 3-5VDC input
3Vo
3.3V regulator output from the breakout; Adafruit states up to 100mA can be taken from this pin.
Type · powerVoltage · 3.3V output, up to 100mA
GND
Common ground for power and logic.
Type · groundVoltage · 0V
SCK
I2C clock pin; also the SPI clock input when using SPI.
Type · signalVoltage · Logic level follows VIN, 3-5V logic safe
SDI
I2C data pin; also SPI data in / MOSI for data sent from the processor to the LPS33/LPS35 sensor.
Type · signalVoltage · Logic level follows VIN, 3-5V logic safe

Start wiring

I2C · SPI · Single data line · 3.3 – 5 V · Breakout

Confirm the data interface matches your host board.

Module pins: VIN, 3Vo, GND, SCK, SDI, SDO, CS, INT. Schematik maps them to your board in the app.

Temp & humidity

165 other options

DHT/AHT sensors, SHT-series humidity chips, BMP and LPS barometers, BME combined sensors, DS18B20 probes, thermocouple amplifiers and non-contact MLX IR sensors — about 165 listings, very different accuracy classes.

View all 165

Gravity: Analog LM35 Temperature Sensor For Arduino visual preview

Related groups

4 groups

Biometrics

UART/I2C fingerprint modules, MAX30102 PPG breakouts, and analog ECG/EMG front-ends for access control and hobby biometric sensing.

Sensors · Biometric sensors · 24 parts

Cameras

Pi CSI modules, USB cameras, MCU-class OV2640/OV5640 boards, on-camera AI like HuskyLens and OpenMV, and thermal or ToF imagers — over 130 listings across very different pipelines.

Sensors · Cameras & vision · 139 parts

Power monitors

INA-series I2C monitors, Hall-effect sensors like the ACS723 and Gravity 20A/50A boards, and non-invasive CT clamps for everything from 3.3V rail telemetry to mains current sensing.

Sensors · Current & voltage · 24 parts

Distance sensors

About 180 listings spanning VL53-series ToF breakouts, HC-SR04 and MaxSonar ultrasonics, 360° triangulation LiDARs, IR proximity sensors, 24GHz mmWave presence detection and laser break-beam sensors.

Sensors · Distance sensors · 178 parts

Pin	Type	Function	Voltage
VIN	power	Power input for the breakout; Adafruit states the onboard regulator accepts 3-5VDC and converts it to 3.3V for the sensor.	3-5VDC input
3Vo	power	3.3V regulator output from the breakout; Adafruit states up to 100mA can be taken from this pin.	3.3V output, up to 100mA
GND	ground	Common ground for power and logic.	0V
SCK	signal	I2C clock pin; also the SPI clock input when using SPI.	Logic level follows VIN, 3-5V logic safe
SDI	signal	I2C data pin; also SPI data in / MOSI for data sent from the processor to the LPS33/LPS35 sensor.	Logic level follows VIN, 3-5V logic safe
SDO	signal	SPI data out / MISO for data sent from the LPS33/LPS35 sensor to the processor; leave disconnected for I2C use.	Logic level follows VIN, 3-5V logic safe
CS	signal	SPI chip-select input; pull low to start an SPI transaction; leave disconnected for I2C use.	Logic level follows VIN, 3-5V logic safe
INT	signal	Interrupt output configurable for pressure threshold events; low-pressure threshold works in relative mode according to Adafruit.	Interrupt output level is the same as Vcc
STEMMA QT	connector	STEMMA QT / Qwiic I2C connector carrying the board I2C and power interface.	Same I2C/power interface as VIN/GND/SCK/SDI

Pinout

Start wiring

Biometrics

Cameras

Power monitors

Distance sensors